Fixed length: 52.0 in. Sold per piece (EA). Quantity 1 = one tube at this fixed length.
Full Product Details
Nylatech PVM Cast Nylon 6 Tube. Modified cast PA6 for components where bearing pressure and sliding speed drive material selection.
Select your tube size
6.25–10.5 in outside diameter (OD). Select OD, then inside diameter (ID).
Sold each (EA): quantity 1 = one complete tube. Standard length: 52 in. Length is not a separate option.
Choosing PVM
Compare PVM with Oil-Filled, MD-Oil or SL for your operating conditions. Selection depends on pressure, speed, temperature and lubrication; a PV figure is not a universal design limit.
Tube is machining stock for bushings, sleeves and rings, not finished bearings or pressure-rated pipe. Nominal wall thickness = (OD − ID) ÷ 2.
Allow for machining: dimensions are nominal stock sizes, not finished-part tolerances. Nylon absorbs moisture; consider dimensional change, temperature, chemicals and operating loads when specifying close-fitting parts.
Technical properties and data sheet
Nylatech PVM — typical selection data
Density
1.13 g/cm³
Tensile strength
10,000 psi
Compressive strength at 10% deflection
14,000–15,000 psi
Flexural strength
13,000 psi
Elongation
20 %
Hardness
79–81 Shore D
Coefficient of friction (dry against steel)
0.14 dimensionless
Water absorption, 24 hours
0.5 %
Typical values, not finished-part performance guarantees. Compressive strength is at 10% deflection; dry-friction values refer to steel where stated. Nylatech PVM technical data.
For custom tube sizes or lengths, or CNC-machined parts, send grade, OD, ID, length and piece count. Include a drawing and required tolerances for machined parts. Request custom work.
Pickup currently unavailable at Kelowna, BC
Nylatech PVM Cast Nylon 6 Tube — 6.25–10.5 in OD
SKU: NPVMT-6.25-3
It appears you are visiting from a region serviced locally by our Nanaimo Franchise.
Nylatech PVM Cast Nylon 6 Tube. Modified cast PA6 for components where bearing pressure and sliding speed drive material selection.
Select your tube size
6.25–10.5 in outside diameter (OD). Select OD, then inside diameter (ID).
Sold each (EA): quantity 1 = one complete tube. Standard length: 52 in. Length is not a separate option.
Choosing PVM
Compare PVM with Oil-Filled, MD-Oil or SL for your operating conditions. Selection depends on pressure, speed, temperature and lubrication; a PV figure is not a universal design limit.
Tube is machining stock for bushings, sleeves and rings, not finished bearings or pressure-rated pipe. Nominal wall thickness = (OD − ID) ÷ 2.
Allow for machining: dimensions are nominal stock sizes, not finished-part tolerances. Nylon absorbs moisture; consider dimensional change, temperature, chemicals and operating loads when specifying close-fitting parts.
Technical properties and data sheet
Nylatech PVM — typical selection data
Density
1.13 g/cm³
Tensile strength
10,000 psi
Compressive strength at 10% deflection
14,000–15,000 psi
Flexural strength
13,000 psi
Elongation
20 %
Hardness
79–81 Shore D
Coefficient of friction (dry against steel)
0.14 dimensionless
Water absorption, 24 hours
0.5 %
Typical values, not finished-part performance guarantees. Compressive strength is at 10% deflection; dry-friction values refer to steel where stated. Nylatech PVM technical data.
For custom tube sizes or lengths, or CNC-machined parts, send grade, OD, ID, length and piece count. Include a drawing and required tolerances for machined parts. Request custom work.
